radius ratio造句
例句與造句
- The effect of the radius ratios of the hollow cylinder to the wave propagation is also discussed
還討論了壓電圓柱殼體半徑比對波傳播的影響。 - Simulation results show that better atomization can be realized by enhancing the cavitation intensity via increasing the injection pressure difference or decreasing the nozzle inlet round angle - radius ratio
通過模擬計算可知，提高噴射壓差和減小噴孔入口圓角半徑都可以提高空穴強度，同時也發現提高噴孔長徑比可以使空穴在噴孔出口截面上分布更為均勻。 - Based on this model , the effects of geometric and structural parameters , such as injection pressure , rear pressure , length - diameter ratio , inlet round angle - radius ratio and non - axis symmetry of nozzle , on the distribution of the cavitation inside the nozzle are analyzed
基于這一模型進一步分析了噴射壓力、背壓和噴孔長徑比、噴孔入口圓角比、非軸對稱噴孔等幾何結構參數對噴孔內空穴分布的影響。 - The threshold speed and the typical characteristics of the oil whip of the system are simulated under the nonlinear model of oil film force , and the state of motion and type of the bifurcation are analyzed by floquet multiplicators which is computed by the shooting method . secondly , the the nonlinear dynamical model of the low - pressure rotor - bearing system by column bearing with reduced dimensions is presented . the numerical results show the rule of the amplitude with the eccentricity of rotor , the length - to - diameter ratio , oil viscosity and the clearance - to - radius ratio of the bearing under the definite speed
其次,對降維后的低壓轉子?軸承系統的非線性動力學方程,計算了圓柱瓦軸承支撐的轉子系統的振動穩定性在固定轉速下隨偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比的變化規律,并分析了轉子前軸承軸頸的失穩轉速與轉子偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比之間的關系,同時利用floquet理論分析其運動狀態和分岔類型。 - In this thesis theoretical solution of inhomogeneous polar orthotropic plate was deduced and plate with clamped edges was taken as example . the displacement in radius direction , inner - force in radius direction , inner - force in annulus direction and buckling load with different core - radius ratio were worked out . the effect of core - radius ratio to the result was discussed in the conclusion
本文從理論上推導出了非均勻極正交各向異性圓板的精確解，并且以夾支圓板作為算例，計算了在不同核徑比的情況下，圓板受外部縱向均布載荷作用后的徑向位移、徑向內力、環向內力，以及屈曲載荷，討論了核徑比對計算結果的影響。 - It's difficult to find radius ratio in a sentence. 用radius ratio造句挺難的
- With the calculation result we can find that the inhomogeneous takes much less effects on the result with small core - radius ratio than that with great core - radius ratio and the small core - radius ratio ' s effect can be ignored , thus the calculation is same as homogeneous plate . the plate with great core - radius ratio should be calculated referenced the means given in this thesis
計算結果表明，在過渡區域很小的情況下，不均勻性對圓板計算結果的影響也很小，基本上可以忽略不計，按照均勻圓板計算；當過渡區域和半徑相比較大的情況下，不均勻性對計算結果的影響變得非常明顯，此時，工程上的設計計算應該參考本文提出的方法進行。